aix:power10_hmc
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
aix:power10_hmc [2024/02/09 21:49] manu |
aix:power10_hmc [2024/02/09 22:13] (current) manu |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Initialize Power 10 with eBMC ====== | ====== Initialize Power 10 with eBMC ====== | ||
| + | |||
| + | https://community.ibm.com/community/user/power/blogs/hariganesh-muralidharan1/2022/07/27/whats-new-in-hmc-10110200 | ||
| + | |||
| + | https://www.ibm.com/support/pages/ibm-power-systems-power10-servers | ||
| + | |||
| + | https://www.ibm.com/support/pages/connecting-power-10-ebmc-system-hmc | ||
| Before Power 10, only one IP address was requested on power servers ASMI to manage it. | Before Power 10, only one IP address was requested on power servers ASMI to manage it. | ||
| - | Now you have first the eBMC, but before starting a power 10, also add a VMI IP address. | + | FIXME Now you have first the eBMC, but before starting a power 10, also add a VMI IP address. |
| + | default login/password for eBMC: admin / admin | ||
| + | |||
| + | FIXME **There are no default IP addresses anymore**, to access ASM (eBMC) using a browser. You should use **panel function 30** to what the IP address may be set to. Panel is located in front of the server, you have buttons: up, down and select | ||
| {{aix:p10_ebmc01.png?650|}} | {{aix:p10_ebmc01.png?650|}} | ||
| Line 11: | Line 21: | ||
| If you use DHCP on the HMC, the eBMC of Power 10 'll appear into HMC interface. Do not start the Power, first you have to set a password, it's both HMC access and admin password for the eBMC. | If you use DHCP on the HMC, the eBMC of Power 10 'll appear into HMC interface. Do not start the Power, first you have to set a password, it's both HMC access and admin password for the eBMC. | ||
| - | Before power on the server, right click, or action, and configure VMI (IP address), if IP is static, then configure one, else change to DHCP. | + | Before power on the server choose **action**, and **VMI configuration** (IP address), if IP is static, then configure one, else change to DHCP. |
| + | Select the same eBMC network interface the HMC is cabled to. | ||
| + | Note that the adapters may list eth1 first, however eth0 is typically used for the first HMC. If 2 HMC are used, both have to be setup | ||
| + | |||
| + | //Note// the eBMC port used on the Power 10 system (first (T0) HMC port = eth0, second (T1)HMC port = eth1) | ||
| + | |||
| + | If this step is missed, when server is started, you 'll have a connection lost on the HMC ! | ||
| Now you're able to power on. | Now you're able to power on. | ||
| Line 17: | Line 33: | ||
| You can either see the power progress on | You can either see the power progress on | ||
| * the HMC | * the HMC | ||
| - | * on eBMC web interface connecting as admin | + | * on eBMC web interface connecting as admin, you have **host console** |
| * using ssh admin@<eBMC> -p 2200 | * using ssh admin@<eBMC> -p 2200 | ||
| FIXME The VMI interfaces share the physical connection of the eBMC ports but have their own IP (DHCP or static) | FIXME The VMI interfaces share the physical connection of the eBMC ports but have their own IP (DHCP or static) | ||
aix/power10_hmc.1707511749.txt.gz · Last modified: 2024/02/09 21:49 by manu
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
