hardware:pureflex_network
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
hardware:pureflex_network [2023/11/28 20:47] manu [Upgrade firmware] |
hardware:pureflex_network [2023/11/28 20:55] (current) manu [Upgrade firmware] |
||
|---|---|---|---|
| Line 421: | Line 421: | ||
| * In Privileged EXEC mode, enter the following command | * In Privileged EXEC mode, enter the following command | ||
| + | <cli> | ||
| + | EN4093R# copy {sftp|tftp|ftp} {image1|image2|boot-image} | ||
| + | </cli> | ||
| * Enter the hostname or IP address of the SFTP, FTP or TFTP server | * Enter the hostname or IP address of the SFTP, FTP or TFTP server | ||
| + | Address or name of remote host: <name or IP address> | ||
| * Enter the name of the new software file on the server. | * Enter the name of the new software file on the server. | ||
| + | <cli> | ||
| + | Source file name: <filename> | ||
| + | </cli> | ||
| The exact form of the name will vary by server. However, the file location is | The exact form of the name will vary by server. However, the file location is | ||
| normally relative to the SFTP, FTP or TFTP directory (for example, tftpboot). | normally relative to the SFTP, FTP or TFTP directory (for example, tftpboot). | ||
| Line 429: | Line 436: | ||
| Once confirmed, the software will begin loading into the switch. | Once confirmed, the software will begin loading into the switch. | ||
| * When loading is complete, use the following commands to enter Global | * When loading is complete, use the following commands to enter Global | ||
| - | Configuration mode to select which software image (image1 or image2) you want | + | Configuration mode to select which software image (image1 or image2) you want to run in switch memory for the next reboot: |
| - | to run in switch memory for the next reboot: | + | <cli> |
| + | EN4093R# configure terminal | ||
| + | EN4093R(config)# boot image {image1|image2} | ||
| + | </cli> | ||
| The system will then verify which image is set to be loaded at the next reset: | The system will then verify which image is set to be loaded at the next reset: | ||
| + | <cli> | ||
| + | Next boot will use switch software image1 instead of image2. | ||
| + | </cli> | ||
| * Reboot the switch to run the new software: | * Reboot the switch to run the new software: | ||
| + | <cli> | ||
| + | EN4093R(config)# reload | ||
| + | </cli> | ||
| The system prompts you to confirm your request. Once confirmed, the switch will | The system prompts you to confirm your request. Once confirmed, the switch will | ||
| reboot to use the new software | reboot to use the new software | ||
| Line 438: | Line 454: | ||
| **Note:** If you select “No” when asked to confirm the reload, any changes made to | **Note:** If you select “No” when asked to confirm the reload, any changes made to | ||
| the configuration since the last reboot will be lost. | the configuration since the last reboot will be lost. | ||
| + | |||
| + | ===== Recovery ===== | ||
| + | |||
| + | The Boot Management Menu | ||
| + | The Boot Management menu allows you to switch the software image, reset the | ||
| + | switch to factory defaults, or to recover from a failed software download. | ||
| + | You can interrupt the boot process and enter the Boot Management menu from the | ||
| + | serial console port. When the system displays Memory Test, press <Shift + B>. | ||
| + | The Boot Management menu appears. | ||
| + | <code> | ||
| + | Resetting the System ... | ||
| + | Memory Test ................................ | ||
| + | Boot Management Menu | ||
| + | I - Change booting image | ||
| + | C - Change configuration block | ||
| + | R - Boot in recovery mode (tftp and xmodem download of images to | ||
| + | recover switch) | ||
| + | Q - Reboot | ||
| + | E - Exit | ||
| + | Please choose your menu option: | ||
| + | </code> | ||
| + | | ||
| + | The Boot Management menu allows you to perform the following actions: | ||
| + | * To change the booting image, press I and follow the screen prompts. | ||
| + | * To change the configuration block, press C and follow the screen prompts. | ||
| + | * To perform a software image recovery, press R and follow the screen prompts. | ||
| + | * To reboot the switch press Q and follow the screen prompts. | ||
| + | * To exit the Boot Management menu, press E. The booting process continues. | ||
hardware/pureflex_network.1701200857.txt.gz · Last modified: 2023/11/28 20:47 by manu
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
