Differences

This shows you the differences between two versions of the page.

--- monitoring:nagios_san [2021/03/03 00:31]
manu created
+++ monitoring:nagios_san [2023/02/21 22:17] (current)
manu
@@ Line 1: / Line 1: @@
 ====== Nagios SAN check ======
+===== Using Nagios Plugin =====
+https://exchange.nagios.org/directory/Plugins/Hardware/Network-Gear/Brocade/check_snmp_brocade--2D-monitor-Brocade-fibre-channel-switches/details
 Example of check SAN (nagios server)
 <code>
+[root@prnagmgmt01 nagios]# cat san_sw.cfg
+define host{
+        use                     linux-server,host-pnp    ; Inherit default values from the generic-host template
+        host_name               DCAS-SAN02
+        hostgroups              msp-brocade-fc
+        address                 10.0.0.10
+        }
 define service{
-        use                             generic-service,srv-pnp         ; Name of service template to use
+        use                     generic-service,srv-pnp         ; Name of service template to use
         host_name               DCAS-SAN02
-        service_description             Brocade Port 17 Status
+        service_description     Brocade Port 17 Status
-        check_command                   Check_Brocade_Port!17
+        check_command           Check_Brocade_Port!17
-        servicegroups                   SG-Storage
+        servicegroups           SG-Storage
         }
-[root@prnagmgmt01 nagios]# cat conf.d/storage/brocade_template.cfg
+[root@prnagmgmt01 nagios]# cat command.cfg
 #### IBM IMM Template ####
 define command {
@@ Line 29: / Line 42: @@
 define hostgroup{
         hostgroup_name  msp-brocade-fc
-        alias           TECH-IT-MSP Brocade FC Switches
+        alias           Brocade FC Switches
         }
@@ Line 47: / Line 60: @@
         }
 </code>
+===== Using Centreon Plugin =====
+====== Use Nagios add a check Centreon for Brocade ======
+https://docs.centreon.com/pp/integrations/plugin-packs/procedures/network-switchs-brocade-snmp/
+===== SAN swicth config SNMPv1 =====
+First test in SNMPv1 (easier, but not all metrics available
+On SAN switch configure SNMPv1
+<cli prompt='>'>
+sansw1:FID128:admin> snmpconfig --show snmpv1
+SNMPv1 community and trap recipient configuration:
+  Community 1:
+    No trap recipient configured yet
+  Community 2:
+    No trap recipient configured yet
+  Community 3:
+    No trap recipient configured yet
+  Community 4:
+    No trap recipient configured yet
+  Community 5:
+    No trap recipient configured yet
+  Community 6:
+    No trap recipient configured yet
+SNMPv1:Enabled
+sansw1:FID128:admin> snmpconfig --add snmpv1 -index 4 -community public -groupname ro
+Committing configuration.....done.
+sansw1:FID128:admin> snmpconfig --show snmpv1
+SNMPv1 community and trap recipient configuration:
+  Community 1:
+    No trap recipient configured yet
+  Community 2:
+    No trap recipient configured yet
+  Community 3:
+    No trap recipient configured yet
+  Community 4: public (ro)
+    No trap recipient configured yet
+  Community 5:
+    No trap recipient configured yet
+  Community 6:
+    No trap recipient configured yet
+SNMPv1:Enabled
+sansw1:FID128:admin> version
+Kernel:     4.1.35rt41
+Fabric OS:  v9.0.1c
+</cli>
+Test SNMP communication from nagios server
+<cli prompt='$'>
+[nagios@nagsrv1 ~]$ snmpwalk -v 1 -c public sansw1
+...
+IF-MIB::ifDescr.1073741828 = STRING: FC port 0/4
+IF-MIB::ifDescr.1073741829 = STRING: FC port 0/5
+...
+</cli>
+===== Plugin Centreon =====
+Enable EPEL and codeready repository (cf DNF)
+<cli prompt='#'>
+[root@lnxb085t yum]# dnf repolist
+Updating Subscription Management repositories.
+repo id                                               repo name
+codeready-builder-for-rhel-8-ppc64le-rpms             Red Hat CodeReady Linux Builder for RHEL 8 Power, little endian
+epel                                                  Extra Packages for Enterprise Linux 8 - ppc64le
+</cli>
+Install snmp packages on nagios
+<cli prompt='#'>
+[root@nagsrv1 ~]# dnf install net-snmp-perl net-snmp-utils net-snmp-agent-libs net-snmp net-snmp-libs perl-XML-LibXML perl-JSON perl-libwww-perl perl-XML-XPath perl-Net-Telnet perl-Net-DNS perl-DBI perl-DBD-MySQL perl-DBD-Pg
+[root@nagsrv1 ~]# dnf install nagios-plugins-perl
+</cli>
+Download the centreon check for brocade:
+  https://download.centreon.com/
+    select --> Custom Platforms --> Plugins
+    Extract from tar.gz package the latest script for brocade : centreon-plugins-20220414/centreon_brocade.pl
+    Copy it to /usr/lib64/nagios/plugins on nagios server
+Test the perl script:
+<cli prompt='#'>
+[root@nagsrv1 plugins]# perl centreon_brocade.pl --plugin=os::linux::snmp::plugin --mode=load
+UNKNOWN: Cannot load module --plugin.
+Can't locate os/linux/snmp/plugin.pm in @INC (you may need to install the os::linux::snmp::plugin module)
+...
+</cli>
+Some perl libraries from centreon are missing
+Check Perl libraries location
+<cli prompt='#'>
+[root@nagsrv1 ~]# perl -e 'print join("\n",@INC)'
+/usr/local/lib64/perl5
+/usr/local/share/perl5
+/usr/lib64/perl5/vendor_perl
+/usr/share/perl5/vendor_perl
+/usr/lib64/perl5
+/usr/share/perl5
+</cli>
+Create your own folder to prevent interaction with anything
+<cli prompt='#'>
+[root@nagsrv1 plugins]# ll /usr/local/lib64/perl5
+ls: cannot access '/usr/local/lib64/perl5': No such file or directory
+[root@nagsrv1 plugins]# mkdir /usr/local/lib64/perl5
+</cli>
+Download the source packages from gihub (source code)
+  https://github.com/centreon/centreon-plugins/releases
+  Extract it and copy the content of src folder into your new created perl repository
+<cli prompt='#'>
+[root@nagsrv1 ~]# cd /usr/local/lib64/perl5
+[root@nagsrv1 perl5]# ls -l
+drwxrwxr-x 78 root root 4096 Jan 18 15:50 apps
+drwxrwxr-x  4 root root   39 Jan 18 15:50 blockchain
+drwxrwxr-x  4 root root   35 Jan 18 15:50 centreon
+drwxrwxr-x  6 root root  113 Jan 18 15:50 centreon-plugins-20230118
+-rwxrwxr-x  1 root root  989 Jan 18 15:50 centreon_plugins.pl
+drwxrwxr-x 17 root root 4096 Jan 18 15:50 cloud
+drwxrwxr-x  3 root root   86 Jan 18 15:50 contrib
+drwxrwxr-x 19 root root 4096 Jan 18 15:50 database
+drwxrwxr-x  4 root root  107 Jan 18 15:50 example
+drwxrwxr-x 11 root root  127 Jan 18 15:50 hardware
+drwxrwxr-x 90 root root 4096 Jan 18 15:50 network
+drwxrwxr-x 12 root root  158 Jan 18 15:50 notification
+drwxrwxr-x 11 root root  124 Jan 18 15:50 os
+drwxrwxr-x  3 root root   18 Jan 18 15:50 snmp_standard
+drwxrwxr-x 29 root root 4096 Jan 18 15:50 storage
+</cli>
+Create the required temporary folder for centreon plugin
+<cli>
+mkdir /var/lib/centreon/centplugins
+chown nagios.nagios /var/lib/centreon/centplugins
+</cli>
+Try again a connection
+<cli prompt='$'>
+[root@nagsrv1 plugins]$ cd /usr/lib64/nagios/plugins/
+[root@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=interfaces --hostname=sansw1 --snmp-version='1' --snmp-community='public' --interface='' --name --add-status --add-traffic --critical-status='' --warning-in-traffic='' --critical-in-traffic='' --warning-out-traffic='' --critical-out-traffic='' --use-new-perfdata
+OK: All interfaces are ok | 'FC port 0/4#interface.traffic.in.bitspersecond'=2983594.46b/s;;;0;4294967295 'FC port
+/4#interface.traffic.out.bitspersecond'=9405745.49b/s;;;0;4294967295 'FC port
+/5#interface.traffic.in.bitspersecond'=3063697.14b/s;;;0;4294967295 'FC port
+/5#interface.traffic.out.bitspersecond'=8112194.39b/s;;;0;4294967295 'FC port
+/6#interface.traffic.in.bitspersecond'=848108.57b/s;;;0;4294967295 'FC port
+...
+/47#interface.traffic.in.bitspersecond'=8957399.45b/s;;;0;4294967295 'FC port
+/47#interface.traffic.out.bitspersecond'=3692879.80b/s;;;0;4294967295
+'lo#interface.traffic.in.bitspersecond'=7320.76b/s;;;0; 'lo#interface.traffic.out.bitspersecond'=7320.76b/s;;;0;
+'eth0#interface.traffic.in.bitspersecond'=22688.20b/s;;;0;1000000000
+'eth0#interface.traffic.out.bitspersecond'=25653.90b/s;;;0;1000000000
+</cli>
+===== Brocade plugin usage =====
+Howto get right syntax ?
+<cli prompt='#'>
+[root@nagsrv1 plugins]# perl ./centreon_brocade.pl --list-plugin
+----------------
+PLUGIN: network::brocade::snmp::plugin
+Plugin Description:
+    Check Brocade hardware in SNMP.
+</cli>
+<cli prompt='#'>
+[root@nagsrv1 plugins]# perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --help
+Plugin Description:
+    Check Brocade hardware in SNMP.
+Global Options:
+    --mode  Choose a mode.
+    --dyn-mode
+            Specify a mode with the path (separated by '::').
+    --list-mode
+            List available modes.
+...
+</cli>
+<cli prompt='#'>
+[root@nagsrv1 plugins]# perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --list-mode
+Plugin Description:
+    Check Brocade hardware in SNMP.
+...
+Modes Available:
+   cpu
+   hardware
+   interfaces
+   list-interfaces
+   memory
+</cli>
+<cli prompt='#'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=hardware  --hostname=sansw1 --snmp-version='1' --snmp-community='public'
+OK: All 1 components are ok [1/1 switch]. | 'count_switch'=1;;;;
+</cli>
+FIXME some checks are not available using SNMPv1
+<cli prompt='#'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=cpu  --hostname=sansw1 --snmp-version='1' --snmp-community='public'
+UNKNOWN: SNMP GET Request : Cant get a single value.
+</cli>
+===== Switching on SNMPv3 for full feature =====
+<cli prompt='>'>
+sansw1:FID128:admin> snmpconfig --show snmpv3
+SNMP Informs = 0 (OFF)
+SNMPV3 user password encrypted  = 0 (OFF)
+SNMPv3 USM configuration:
+User 1 (ro): snmpuser1
+        Auth Protocol: noAuth
+        Priv Protocol: noPriv
+User 2:
+User 3:
+User 4:
+User 5:
+User 6:
+User 7:
+User 8:
+User 9:
+User 10:
+User 11:
+User 12:
+SNMPv3 Trap/Informs configuration:
+Trap Entry 1:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 2:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 3:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 4:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 5:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 6:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+</cli>
+<cli prompt='>'>
+sansw1:FID128:admin> snmpconfig --add snmpv3 -index 6 -user test6 -groupname rw -auth_proto 1 -auth_passwd myauthpassword -priv_proto 1 -priv_passwd myprivpassword
+Committing configuration.....done.
+sansw1:FID128:admin> snmpconfig --show snmpv3
+SNMP Informs = 0 (OFF)
+SNMPV3 user password encrypted  = 0 (OFF)
+SNMPv3 USM configuration:
+User 1 (ro): snmpuser1
+        Auth Protocol: noAuth
+        Priv Protocol: noPriv
+User 2:
+User 3:
+User 4:
+User 5:
+User 6 (rw): test6
+        Auth Protocol: MD5
+        Priv Protocol: DES
+User 7:
+User 8:
+User 9:
+User 10:
+User 11:
+User 12:
+SNMPv3 Trap/Informs configuration:
+Trap Entry 1:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 2:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 3:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 4:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 5:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+Trap Entry 6:     No trap recipient configured yet
+    Notify Type: TRAP(1)
+</cli>
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ snmpwalk -v3 -l authPriv -u test6 -a MD5 -A  myauthpassword -x DES -X myprivpassword sansw1
+SNMPv2-MIB::sysDescr.0 = STRING: Fibre Channel Switch.
+SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.1588.2.1.1.181
+DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3385689700) 391 days, 20:41:37.00
+SNMPv2-MIB::sysContact.0 = STRING: Field Support.
+SNMPv2-MIB::sysName.0 = STRING: sansw1
+SNMPv2-MIB::sysLocation.0 = STRING: End User Premise.
+SNMPv2-MIB::sysServices.0 = INTEGER: 79
+IF-MIB::ifNumber.0 = INTEGER: 68
+IF-MIB::ifIndex.805306369 = INTEGER: 805306369
+IF-MIB::ifIndex.805306370 = INTEGER: 805306370
+IF-MIB::ifIndex.805306371 = INTEGER: 805306371
+IF-MIB::ifIndex.805306372 = INTEGER: 805306372
+IF-MIB::ifIndex.805306373 = INTEGER: 805306373
+IF-MIB::ifIndex.805306374 = INTEGER: 805306374
+IF-MIB::ifIndex.805306375 = INTEGER: 805306375
+</cli>
+Now changing user to RO
+<cli prompt='>'>
+sansw1:FID128:admin> snmpconfig --set snmpv3 -index 6 -user test6 -groupname ro
+Committing configuration.....done.
+sansw1:FID128:admin> snmpconfig --show snmpv3
+...
+User 6 (ro): test6
+</cli>
+Test
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=cpu --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword'
+OK: CPU Usage: 14.00% | 'cpu'=14%;;;0;100
+</cli>
+===== Check examples =====
+CPU
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=cpu --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword' --warning=60 --critical=90
+OK: CPU Usage: 2.00% | 'cpu'=2%;0:60;0:90;0;100
+</cli>
+Hardware
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=hardware --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword'
+OK: All 18 components are ok [17/17 sensors, 1/1 switch]. | 'sensor_SLOT #0: TEMP #1'=32celsius;;;; 'sensor_SLOT #0: TEMP #2'=33celsius;;;; 'sensor_SLOT #0: TEMP #3'=31celsius;;;; 'sensor_SLOT #0: TEMP #4'=29celsius;;;; 'sensor_SLOT #0: TEMP #5'=30celsius;;;; 'sensor_SLOT #0: TEMP #6'=33celsius;;;; 'sensor_SLOT #0: TEMP #7'=30celsius;;;; 'sensor_SLOT #0: TEMP #8'=40celsius;;;; 'sensor_SLOT #0: TEMP #9'=54celsius;;;; 'sensor_SLOT #0: TEMP #10'=23celsius;;;; 'sensor_SLOT #0: TEMP #11'=24celsius;;;; 'sensor_SLOT #0: TEMP #12'=45celsius;;;; 'sensor_FAN #1'=12821rpm;;;; 'sensor_FAN #2'=13071rpm;;;; 'count_sensor'=17;;;; 'count_switch'=1;;;;
+</cli>
+Memory
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=memory --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword' --warning=60 --critical=90
+OK: Memory Usage: 27.00% used | 'used'=27%;0:60;0:90;0;100
+</cli>
+Ports
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=interfaces --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword'
+CRITICAL: Interface 'FC port 0/19' Status : down (admin: up) - Interface 'FC port 0/23' Status : down (admin: up) - Interface 'FC port 0/28' Status : down (admin: up) - Interface 'FC port 0/29' Status : down (admin: up) - Interface 'FC port 0/33' Status : down (admin: up) - Interface 'FC port 0/35' Status : down (admin: up)
+</cli>
+Interfaces status
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=list-interfaces --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword'
+List interfaces:
+'FC port 0/4' [speed = 8000][status = up][id = 1073741828][type = fibreChannel]
+'FC port 0/5' [speed = 8000][status = up][id = 1073741829][type = fibreChannel]
+'FC port 0/6' [speed = 8000][status = up][id = 1073741830][type = fibreChannel]
+'FC port 0/7' [speed = 8000][status = up][id = 1073741831][type = fibreChannel]
+</cli>
+All interfaces, bypass errors
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=interfaces --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword' --warning-status='' --critical-status=''
+OK: All interfaces are ok
+</cli>
+Check Gbic optical strenght
+<cli prompt='$'>
+[nagios@nagsrv1 plugins]$ perl ./centreon_brocade.pl --plugin=network::brocade::snmp::plugin --mode=interfaces --hostname=sansw1 --snmp-version='3' --snmp-username='test6' --authprotocol='MD5' --authpassphrase='myauthpassword' --privprotocol='DES' --privpassphrase='myprivpassword' --name --warning-status='' --critical-status=''  --add-optical --add-status | sed 's/laser_temp_FC\ /#FC_/g' | tr '#' '\n'
+OK: All interfaces are ok | '
+FC_port 0/4'=39.00C;;;; 'input_power_FC port 0/4'=-2.6dBm;;;; 'output_power_FC port 0/4'=-1.5dBm;;;; '
+FC_port 0/5'=41.00C;;;; 'input_power_FC port 0/5'=-1.6dBm;;;; 'output_power_FC port 0/5'=-2.1dBm;;;; '
+FC_port 0/6'=43.00C;;;; 'input_power_FC port 0/6'=-2.1dBm;;;; 'output_power_FC port 0/6'=-2.2dBm;;;; '
+FC_port 0/7'=42.00C;;;; 'input_power_FC port 0/7'=-3.3dBm;;;; 'output_power_FC port 0/7'=-2.1dBm;;;; '
+FC_port 0/8'=44.00C;;;; 'input_power_FC port 0/8'=-0.2dBm;;;; 'output_power_FC port 0/8'=-0.2dBm;;;; '
+FC_port 0/9'=45.00C;;;; 'input_power_FC port 0/9'=-2.4dBm;;;; 'output_power_FC port 0/9'=-1.1dBm;;;; '
+...
+FC_port 0/19'=43.00C;;;; 'output_power_FC port 0/19'=-1.1dBm;;;; '
+</cli>
+Add this paragraph to your command.cfg in nagios
+<code>
+define command{
+       command_name    check_brocade_health
+       command_line    $USER1$/centreon_brocade.sh -H $HOSTADDRESS$ -c $ARG1$
+       }
+</code>
+<cli prompt='$'>
+[nagios@nagsrv1 ~]$ cat /usr/lib64/nagios/plugins/centreon_brocade.sh
+</cli>
+<code>
+#!/bin/bash
+#@(#) Check SAN switch status
+# Version 1.0  02-2023 EIF
+while test -n "$1"; do
+    case "$1" in
+        -H) host=$2
+            shift ;;
+        -c) element=$2
+            shift ;;
+        esac
+    shift
+done
+#host=$1
+#element=$2
+warning=60
+critical=90
+snmpuser='test6'
+snmpv='3'
+authprot='MD5'
+authpass='myauthpassword'
+privprot='DES'
+privpass='myprivpassword'
+prog=/usr/lib64/nagios/plugins/centreon_brocade.pl
+if [[ "${element}" == "cpu" ]]
+then
+  perl ${prog} --plugin=network::brocade::snmp::plugin --mode=${element} --hostname=${host} --snmp-version=${snmpv} --snmp-username=${snmpuser} --authprotocol=${authprot} --authpassphrase=${authpass} --privprotocol=${privprot} --privpassphrase=${privpass} --warning=60 --critical=90
+else
+  if [[ "${element}" == "hardware" ]]
+  then
+    perl ${prog} --plugin=network::brocade::snmp::plugin --mode=${element} --hostname=${host} --snmp-version=${snmpv} --snmp-username=${snmpuser} --authprotocol=${authprot} --authpassphrase=${authpass} --privprotocol=${privprot} --privpassphrase=${privpass}
+  else
+    if [[ "${element}" == "memory" ]]
+    then
+      perl ${prog} --plugin=network::brocade::snmp::plugin --mode=${element} --hostname=${host} --snmp-version=${snmpv} --snmp-username=${snmpuser} --authprotocol=${authprot} --authpassphrase=${authpass} --privprotocol=${privprot} --privpassphrase=${privpass} --warning=60 --critical=90
+    else
+      if [[ "${element}" == "list-interfaces" ]]
+      then
+        perl ${prog} --plugin=network::brocade::snmp::plugin --mode=${element} --hostname=${host} --snmp-version=${snmpv} --snmp-username=${snmpuser} --authprotocol=${authprot} --authpassphrase=${authpass} --privprotocol=${privprot} --privpassphrase=${privpass}
+        perl ${prog} --plugin=network::brocade::snmp::plugin --mode=interfaces --hostname=${host} --snmp-version=${snmpv} --snmp-username=${snmpuser} --authprotocol=${authprot} --authpassphrase=${authpass} --privprotocol=${privprot} --privpassphrase=${privpass} --name --warning-status='' --critical-status=''  --add-optical --add-status | sed 's/laser_temp_FC\ /#FC_/g' | tr '#' '\n'
+      else
+        if [[ "${element}" == "interfaces" ]]
+        then
+          perl ${prog} --plugin=network::brocade::snmp::plugin --mode=${element} --hostname=${host} --snmp-version=${snmpv} --snmp-username=${snmpuser} --authprotocol=${authprot} --authpassphrase=${authpass} --privprotocol=${privprot} --privpassphrase=${privpass} | sed 's/FC\ port\ /FC_/g' | sed 's/\ //g' | sed 's/\]//g'| sed 's/\[/;/g' | sed "s/'//g" | sed "s/$/;$(date '+%s')/"
+        fi
+      fi
+    fi
+  fi
+fi
 </code>

wiki

User Tools

Site Tools

Differences

Page Tools