Differences

This shows you the differences between two versions of the page.

--- storage:svc_cmd [2021/12/10 15:06]
manu [Manualy upgrade controler firmware/software]
+++ storage:svc_cmd [2025/03/21 23:03] (current)
manu [Replace SVC node]
@@ Line 323: / Line 323: @@
 //Error// using replication metro mirror (PPRC) or global mirror --> change the system layout on all devices to have the same virtualization layer
-==== Enable SVC NPIV ====
+==== Enable SVC NPIV (required in v8.7) ====
 Here we talk about SVC FC port virtualization, host with NPIV is supported for a long time.
+=== Change from Not virtualized to Transitional ===
 Enabling NPIV target port functionality on a new cluster
 After creating the cluster, but before starting to add hosts, issue
-  chiogrp fctargetportmode transitional <IO group>
+<cli>
+  chiogrp -fctargetportmode transitional <IO group>
+</cli>
 on each populated I/O group.
-Once that is done, issue
-  chiogrp fctargetportmode enabled <IO group>
+=== Update the zoning for ports connected to hosts ===
+    Ensure that the hosts are using the NPIV ports for host I/O. To verify that you are logged in to these hosts with these NPIV ports, enter the following command
+<cli>
+lsfabric -host host_id_or_name
+</cli>
+Wait a minimum of 15 minutes before you move from transitional to enabled state.
+=== Change from Transitional to NPIV ===
+To change the NPIV setting to enabled, enter the following command:
+<cli>
+chiogrp -fctargetportmode enabled
+</cli>
 on each populated I/O group.
 If using WWPN based zoning, issue the command to view the set of FC ports.
+<cli>
   lstargetportfc
+</cli>
 All ports that display virtualized=yes need to be zoned into hosts as described above.
@@ Line 459: / Line 479: @@
 </cli>
-==== Manualy upgrade controler firmware/software ====
+==== Manualy upgrade controler firmware/software/reset drives status ====
+If you have pending upgrade on drives, for a long time and never end
+<cli prompt='>'>
+IBM_Storwize:v3700-Quorum:superuser>lsdriveupgradeprogress
+id  status        estimated_completion_time
+   not_scheduled
+   not_scheduled
+  completed     221013120044
+  completed     221013120550
+  completed     221013121056
+  completed     221013121602
+</cli>
+Reset the status to **not_scheduled**
 First copy firmware and test upgrade tool into /home/admin/upgrade
@@ Line 516: / Line 550: @@
 updated to 7.8.1.11 until it has been resolved
 </cli>
+If it keeps schedules pending, then restart **tomcat**
+<cli prompt='>'>
+IBM_Storwize:v3700:superuser> satask restartservice -service tomcat
+IBM_Storwize:v3700:superuser> satask restartservice -service cimom
+</cli>
+Wait about 5 min and then retry the upgrade
 Now you are ready to upgrade the new firmware
@@ Line 522: / Line 563: @@
 </cli>
-====== SVC changing topology for enhanced strech cluster ======
+Use the following command to check the upgrade progress, take care it will stay on 0, after it will switch to 50% after reboot of first controller...
+<cli prompt='>'>
+IBM_Storwize:v3700-Quorum:superuser> lsupdate
+</cli>
+====== SVC changing topology for enhanced stretch cluster ======
 == Configuration steps ==
@@ Line 608: / Line 654: @@
 mkvdisk -mdiskgrp pool1 -iogrp io_grp0 -size 1099511627776 -unit b -name DCAV-PRTSM02-99
 </cli>
+===== Users management =====
+==== Groups ====
+List groups:
+<cli prompt='>'>
+IBM_FlashSystem:fs7300:user01> lsusergrp
+id name            role            remote owner_id owner_name
+  SecurityAdmin   SecurityAdmin   no
+  Administrator   Administrator   no
+  CopyOperator    CopyOperator    no
+  Service         Service         no
+  Monitor         Monitor         no
+  RestrictedAdmin RestrictedAdmin no
+</cli>
+==== Users ====
+Create a new user with a password:
+<cli prompt='>'>
+IBM_FlashSystem:fs7300:user01> mkuser -name user02 -usergrp SecurityAdmin -password xxxxxx
+</cli>
+List all users
+<cli prompt='>'>
+IBM_FlashSystem:fs7300:user01> lsuser
+id name           password ssh_key remote usergrp_id usergrp_name
+  superuser      yes      yes     no     0          SecurityAdmin
+  user02         yes      no      no     0          SecurityAdmin
+  report         no       yes     no     4          Monitor
+</cli>
+Create a user with ssh key axchange
+  * Copy the public key from you user to **/home/admin/upgrade**
+<cli prompt='#'>
+[root@lnx01]/storage/.ssh # scp /storage/.ssh/id_ecdsa.pub user01@fs7300:/home/admin/upgrade
+Password:
+id_ecdsa.pub                                                              100%  284   411.6KB/s   00:00
+</cli>
+  * Create a user and import the ssh key
+<cli prompt='>'>
+IBM_FlashSystem:fs7300:user01>mkuser -name report -usergrp Monitor -keyfile /home/admin/upgrade/id_ecdsa.pub
+User, id [8], successfully created
+</cli>
+===== Replace SVC node ======
+<cli>
+satask installsoftware -file IBM_5.0.12 -ignore
+</cli>
+<cli>
+sainfo lsservicenode
+</cli>
+<cli>
+satask chvpd -wwnn 500507680F00FFFF -fcportmap 11-11,12-12,13-13,14-14,21-21,22-22,23-23,24-24
+</cli>

wiki

User Tools

Site Tools

Differences

Page Tools