wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Brocade command line ======

===== SAN switch first setup =====

==== Set an IP address: ====

- you can connect to the switch with ssh to the IP: **10.77.77.77/255.255.255.0**\\
- or use the serial connection with the following parameters: speed 9600, data bits 8, stop bits 1, parity None, and flow control None

Once connected to the switch with admin/password, set the password for all users, then set the right IP address:
<cli prompt='>'>
IBM_2498_R06:admin> ipaddrshow
SWITCH
Ethernet IP Address: 10.77.77.77
Ethernet Subnetmask: 255.255.255.0
Gateway IP Address: 
DHCP: Off
IPv6 Autoconfiguration Enabled: Yes
Local IPv6 Addresses:
IPv6 Gateways:

IBM_2498_R06:admin> ipaddrset
Ethernet IP Address [10.77.77.77]:10.18.228.31
Ethernet Subnetmask [255.255.255.0]:255.255.255.0
Gateway IP Address [0.0.0.0]:10.18.228.1
DHCP [Off]:
IP address is being changed...Done.
</cli>

==== Set the hostname ====

<cli prompt='>'>
SWSAN1:admin> switchName "SWSANNEW1"
SWSANNEW1
SWSANNEW1:admin> 
</cli>

==== Set the timeone / time server ====

Time zone:
<cli prompt='>'>
S-SRV2FAS-107:admin> tstimezone --interactive
Please identify a location so that time zone rules can be set correctly.
Please select a continent or ocean.
 1) Africa
 2) Americas
 3) Antarctica
 4) Arctic Ocean
 5) Asia
 6) Atlantic Ocean
 7) Australia
 8) Europe
 9) Indian Ocean
10) Pacific Ocean
11) none - I want to specify the time zone using the POSIX TZ format.
Enter number or control-D to quit ? 8
Please select a country.
 1) Aaland Islands         24) Lithuania
 2) Albania                25) Luxembourg
 3) Andorra                26) Macedonia
 4) Austria                27) Malta
 5) Belarus                28) Moldova
 6) Belgium                29) Monaco
 7) Bosnia & Herzegovina   30) Netherlands
 8) Britain (UK)           31) Norway
 9) Bulgaria               32) Poland
10) Croatia                33) Portugal
11) Czech Republic         34) Romania
12) Denmark                35) Russia
13) Estonia                36) San Marino
14) Finland                37) Serbia and Montenegro
15) France                 38) Slovakia
16) Germany                39) Slovenia
17) Gibraltar              40) Spain
18) Greece                 41) Sweden
19) Hungary                42) Switzerland
20) Ireland                43) Turkey
21) Italy                  44) Ukraine
22) Latvia                 45) Vatican City
23) Liechtenstein
Enter number or control-D to quit ? 25

The following information has been given:

        Luxembourg

Therefore TZ='Europe/Luxembourg' will be used.
Local time is now:      Fri Nov 16 15:20:56 CET 2007.
Universal Time is now:  Fri Nov 16 14:20:56 UTC 2007.
Is the above information OK?
1) Yes
2) No
Enter number or control-D to quit ? 1
System Time Zone change will take effect at next reboot
S-SRV2FAS-107:admin> tstimezone
Europe/Luxembourg
S-SRV2FAS-107:admin> date
Fri Nov 16 15:21:28 CET 2007
</cli>

Time server, it needs an ethernet connection to connect to time server, else it will failed:
<cli prompt='>'>
S-SRV2FAS-107:admin> tsclockserver "192.168.20.99" 
Updating Clock Server configuration...done.
S-SRV2FAS-107:admin> tsclockserver
192.168.20.99
</cli>

==== Set the Switch Domain ID ====

**Very important :** The switch Domain ID have to be unique for each switch into a fabric, change it on each switch.\\
<color red>This is an offline operation.</color>
<cli prompt='>'>
SWSAN1:admin> switchshow
switchName:     SWSAN1
switchType:     26.2
switchState:    Online
switchMode:     Native
switchRole:     Principal
switchDomain:   1
.... 
</cli>
<cli prompt='>'>
switch_8:FID8:admin> switchdisable
switch_8:FID8:admin> configure
Configure...
Fabric parameters (yes, y, no, n): [no] y
Domain: (1..239) [1] 4
...
switch_8:FID8:admin>switchenable
</cli>

==== Set the DNS servers ====

<cli prompt='>'>
SWSAN1:admin> dnsconfig

Enter option
1 Display Domain Name Service (DNS) configuration
2 Set DNS configuration
3 Remove DNS configuration
4 Quit
Select an item: (1..4) [4] 1

         Domain Name Server Configuration Information
         ____________________________________________

         Please set domain name and name server IP address

Enter option
1 Display Domain Name Service (DNS) configuration
2 Set DNS configuration
3 Remove DNS configuration
4 Quit
Select an item: (1..4) [4] 2

Enter Domain Name: [] mydomain.com
Enter Name Server IP address in dot notation: [] 10.10.3.2
Enter Name Server IP address in dot notation: [] 10.10.3.1
DNS Configuration has changed

Enter option
1 Display Domain Name Service (DNS) configuration
2 Set DNS configuration
3 Remove DNS configuration
4 Quit
Select an item: (1..4) [4] 4
SWSAN1:admin>
</cli>

==== Firmware Download ====

Before starting a firmware upgrade, save the current configuration on a secure place on a ftp or scp server:
<cli prompt='>'>
SWSAN1:admin> configUpload -p scp 10.10.5.152,root,/backup/swsan1.bkp

root@10.10.5.152's password:
Upload complete
</cli>

Check the firmware version and determine the latest firmware for this kind of switch. In certain conditions, you have to do multiples upgrade \\
to reach the latest level. Check into the readme file the prerequisites.
<cli prompt='>'>
IBM_2498_R06:admin> version
Kernel: 2.6.14.2
Fabric OS: v6.4.1
Made on: Thu Oct 7 00:35:44 2010
Flash: Sat Oct 30 00:02:37 2010
BootProm: 1.0.9
IBM_2498_R06:admin>
</cli>

Set the timeout to 0:
<cli prompt='>'>
IBM_2498_R06:admin> timeout
Current IDLE Timeout is 10 minutes
IBM_2498_R06:admin> timeout 0
IDLE Timeout Changed to 0 minutes
The modified IDLE Timeout will be in effect after NEXT login
IBM_2498_R06:admin>
................................
Logout then re-login
............................
IBM_2498_R06:admin> timeout
Current IDLE Timeout is 0 minutes
</cli>

Put the latest firmware on an FTP server and uncompress it. For most releases, you have to specify the directory path with release.plist: Ex /v4.3.0/release.plist \\
(do not check if this file exists, it is present into subdirectory, but the switch will check which is his firmware directory).\\ 
Download and install the new firmware (disruptive for most kind of switches):
<cli prompt='>'>
SAN32B_3_146:admin> firmwaredownload -p sftp 10.64.210.103,ibm,/export/software/v4.3.0,password
Server IP: 10.64.210.103, Protocol IPv4
Checking system settings for firmwaredownload...
System settings check passed.
You can run firmwaredownloadstatus to get the status
of this command.
This command will cause a warm/non-disruptive boot on the switch,
but will require that existing telnet, secure telnet or SSH sessions
be restarted.
Do you want to continue [Y]: y
Firmware is being downloaded to the switch. This step may take up to 30 
minutes.
Preparing for firmwaredownload...
Start to install packages...
dir ##########################################
ldconfig ##########################################
glibc ##########################################
....
</cli>

After the reboot, check the new firmware version:
<cli prompt='>'>
SAN32B_3_146:admin> firmwareshow
Appl Primary/Secondary Versions
------------------------------------------
FOS  v6.2.0e
     v6.2.0e
SAN32B_3_146:admin> version
Kernel: 2.6.14.2
Fabric OS: v6.2.0e
Made on: Tue Apr 14 21:26:47 2009
Flash: Wed Jul 15 17:02:37 2009
BootProm: 4.6.6
</cli>

==== FPGA upgrade ====

The firmware download does not automatically update the FPGA firmware into the FPGA flash memory of the system. If an updated FPGA version is included in a Fabric OS firmware update, after the firmware download is completed, you must enter the fpgaupgrade command to update the FPGA firmware
<cli prompt='>'>
switch:admin> fpgaupgrade --latest
Current          Latest
-------------------------
0x05.05          0x06.06
</cli>

Upgrade FGPA to latest level
<cli prompt='>'>
switch:admin> fpgaupgrade
This is a disruptive operation and will require a power-cycle after the completion of the operation.
Do you want to continue (y/n) ?
y
Programming new FPGA, this may take a few minutes ...
Device #1 IDCODE is 0310A0DD
full-chip erasing Max 10 FPGA device(s) ...
programming Max 10 FPGA CFM0 block at sector 5 ... 
...
Exit code = 0... Success
Programmed new FPGA successfully. Please power-cycle for it to take effect. 
</cli>

If not success, do not reboot the SAN switch, correct first the error
<cli prompt='>'>
switch:admin> reboot
</cli>
==== SSH keys import ====

If you want to connect automatically to a switch using ssh, you have to import ssh public key for the user.
Copy one or more public keys in a file and put it on a ftp or ssh server. 
<cli prompt='>'>
[root@nim] # ssh admin@switchsan1
switchsan1:admin> sshutil importpubkey
Enter user name for whom key is imported:admin
Enter IP address:172.10.10.165
Enter remote directory:/root/.ssh
Enter public key name(must have .pub suffix):id_rsa.pub
Enter login name:root
root@172.10.10.165's password:
public key is imported successfully.
switchsan1:admin> logout
</cli>

==== Add a user with admin rights ====

<cli prompt='>'>
switchsan1:admin> userconfig --add lpardeploy -l 1-128 -h 128 -r admin -c admin
Setting initial password for lpardeploy
Enter new password:
Re-type new password:
Account lpardeploy has been successfully added.
</cli>

    Access to Virtual Fabrics 1 through 128
    Default home logical switch to 128
    Admin role permissions
    Admin chassis role permissions

==== Backup SAN config ====

Automatic backup of san config:
<cli prompt='>'>
ssh admin@switchsan1 "configupload -all -scp nimsrv,scpuser,/backup/switchsan1.config"
</cli>

===== Step by Step Procedure of Zoning via Cli =====

<cli prompt='>'>
1.Create an Alias using “AliCreate”

SW0:admin> alicreate "SUNX4150_HBA0"
SW0:admin> alicreate "V7000_ctl1_p0","50:00:00:1b:38:13:a8:08"
SW0:admin> aliadd "AIXNPIV_HBA0","c5:00:00:1b:32:13:a8:01;c5:00:00:1b:32:13:a8:02"
In particular situations an alias have more than 1 member.
SW0:admin> alicreate "SUNX4150_HBA1", "1,3"
This is a bad sample, please do not use anymore port zoning.

2.Add member to Alias using “Aliadd”

SW0:admin> aliadd "SUNX4150_HBA0","21:00:00:1b:32:13:a8:9f"


3.Create a Zone using “ZoneCreate”

SW0:admin> zonecreate "CX_424_SPB4_SUNX4150_HBA0"
SW0:admin> zonecreate "Z_AIXNPIV_HBA0_V7000_ctl1_p0","V7000_ctl1_p0;AIXNPIV_HBA0"

4. Add member to Zone using “ZoneAdd”

SW0:admin> zoneadd "CX_424_SPB4_SUNX4150_HBA0","CX_424_SPB4"

5.Add a Zone to Zone configuration “CfgAdd”.

SW0:admin> cfgadd "SAN_U2_SW0_Config","CX_424_SPB4_SUNX4150_HBA0;Z_AIXNPIV_HBA0_V7000_ctl1_p0"

6.Save the Configuration using “CfgSave”.

SW0:admin> cfgsave

7.Enable the Configuration using “CfgEnable”.

SW0:admin> cfgenable "SAN_U2_SW0_Config"
</cli>

Rename an oject (alias, zone) use the following command:
<cli prompt='>'>
switch:admin> zoneobjectrename "alias1","aliasold"
</cli>

==== Command to compare active zoning and defined ====

Compare active and defined config
<cli prompt='>'>
san01:FID128:admin> cfgshow --transdiffsonly
No change in configuration defined
</cli>

If you have specific zone you wish to check you can go with the command zone –validate {zone_name}, example output:
<cli prompt='>'>
switch> zone --validate Z_linux002_storage001_FA8fB
Defined configuration:
 zone:  Z_linux002_storage001_FA8fB
                A_storage001_FA8fb; a_linux002_hba_a

Effective configuration:
 zone:  Z_linux002_storage001_FA8fB
                50:00:09:72:08:28:55:3d
                21:00:00:1b:32:8c:71:c6
</cli>

Count if a zone is available in active and defined config:
  * 1 means, only available in one config
<cli prompt='$'>
$ ssh -l admin switch cfgshow | grep "zone" | sort | uniq -c
admin@switch's password:
      1  zone:  zone_storage3257_FA7bA_RTPUS
      2  zone:  zone_storage3791_10aA_fdsa
      2  zone:  zone_storage3791_10agfda
      2  zone:  zone_storage3791_efs
      2  zone:  zone_storage3791_vfda
      2  zone:  zone_storage3791_grw
      2  zone:  zone_storage3791_fdsbaa
      2  zone:  zone_storage3791_vfaf
</cli>

==== Command to test ==== 

Check if source and target are in a zone
<cli prompt='>'>
switch:admin> fcping 10:00:00:00:c9:29:0e:c4 21:00:00:20:37:25:ad:05
Source: 10:00:00:00:c9:29:0e:c4
Destination: 21:00:00:20:37:25:ad:05
Zone Check: Not Zoned
</cli>

Check if the WWN, PID or alias is still connected or not into the whole fabric
<cli prompt='>'>
DCX01:FID128:admin> nodefind 50:06:04:8a:d5:4f:23:10
Remote:
    Type Pid    COS     PortName                NodeName
    N    40a500;      3;50:06:04:8a:d5:4f:23:10;50:06:04:8a:d5:4f:23:10;
        FC4s: FCP
        PortSymb: [38] "EMC SYMMETRIX 000000000001   "
        NodeSymb: [38] "EMC SYMMETRIX 000000000001   "
        Fabric Port Name: 20:02:00:05:1e:32:12:01
        Permanent Port Name: 50:06:04:8a:d5:4f:23:10
        Device type: Physical Initiator+Target
        Port Index: 165
        Share Area: No
        Device Shared in Other AD: No
        Redirect: No
        Partial: No
    Aliases: Symm0001_alias1
DCX01:FID128:admin> nodefind V7K3_C2_4
No device found
</cli>

Let’s analyze the output.

    Remote means that this WWN is connected to another switch in the Fabric.
    40a500 – is a 24bit (Core PID format) FC Address. I mentioned FC Addressing in Fibre Channel addressing entry if you wish to refresh the knowledge. But in few words – First 8 bits are Domain ID, another 8 bits are Area ID, and last 8 bits are Node ID – 00 or AP_PA, so:
        40 – this is the Domain ID
        a5 – this is the Area ID – a5 hex = 165 dec. As you can see this is exactly – our Port Index.
        00 – this is the Node ID –  00, because to this port only one Node is connected directly / No NPIV. If this switch required shared area addressing (basically more than 255), the first 8 bit of Node ID would be "borrowed" as Area ID as well.
    Port Index: 165 – is already given (as hex) in Core PID Address.

<cli prompt='>'>
switch01> fabricshow

Switch ID   Worldwide Name           Enet IP Addr    FC IP Addr      Name
-------------------------------------------------------------------------
 23: fffc17 10:00:00:05:1e:13:1c:22 192.168.100.3  0.0.0.0        >"switch01"
 24: fffc18 10:00:00:05:1e:13:6e:f2 192.168.100.3  0.0.0.0        "switch04"
 62: fffc3e 10:00:00:05:1e:13:0a:13 192.168.75.1  0.0.0.0         "switch02"
 64: fffc40 10:00:00:05:1e:55:63:3d 192.168.100.3  0.0.0.0        "switch05"
101: fffc65 10:00:00:05:1e:55:33:11 192.168.75.2  0.0.0.0         "switch06"
105: fffc69 10:00:00:05:1e:32:64:01 192.168.117.1 0.0.0.0         "switch07"
</cli>

Above we see the output of our Fabric. What interests us is the ID of the Switch. FFFCxx is the Address of the Domain Controller – xx represents the Domain ID. This is considered as the name/ID of the switch. And there it is – our Switch with Domain_ID=40 is switch05.

<cli prompt='>'>
IBM_SAN18BR_137:admin> switchshow
switchName: IBM_SAN18BR_137
.
15 15 -- N4 No_Module
16 16 -- -- Offline
17 17 -- -- Offline Disabled (Persistent)
.
31 31 -- -- Offline Disabled (Persistent)
ge0 id 1G Online FCIP
ge1 -- 1G No_Module FCIP Disabled (Persistent)
</cli>

Command to check if an alias is present, and port characteristics:
<cli prompt='>'>
SWSAN02:admin> nsaliasshow
{
 Type Pid    COS     PortName                NodeName                 TTL(sec)
 N    2a0000;      3;20:34:00:80:e5:2e:c7:02;20:04:00:80:e5:2e:c7:02; na
    FC4s: FCP [IBM     1746      FAStT 1070]
    Fabric Port Name: 20:00:00:05:1e:34:c5:ef 
    Permanent Port Name: 20:34:00:80:e5:2e:c7:02
    Port Index: 0
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases: ds3524_a_p1
 N    2a0100;    2,3;20:00:00:c0:dd:28:7e:d6;10:00:00:c0:dd:28:7e:d6; na
    Fabric Port Name: 20:01:00:05:1e:34:c5:ef 
    Permanent Port Name: 20:00:00:c0:dd:28:7e:d6
    Port Index: 1
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases:
 N    2a0101;    2,3;21:00:00:24:ff:49:a2:bd;20:00:00:24:ff:49:a2:bd; na
    FC4s: FCP 
    NodeSymb: [38] "QMI2592 FW:v5.06.05 DVR:v902.k1.1-9vmw"
    Fabric Port Name: 20:01:00:05:1e:34:c5:ef 
    Permanent Port Name: 20:00:00:c0:dd:28:7e:d6
    Port Index: 1
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases:
 N    2a0200;    2,3;10:00:00:00:c9:83:90:89;20:00:00:00:c9:83:90:89; na
    FC4s: FCP 
    PortSymb: [34] "Emulex PPN-10:00:00:00:c9:83:90:89"
    NodeSymb: [41] "Emulex LPe11000 FV2.71A2 DV8.2.3.1-127vmw"
    Fabric Port Name: 20:02:00:05:1e:34:c5:ef 
    Permanent Port Name: 10:00:00:00:c9:83:90:89
    Port Index: 2
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases: esx03_p1
 N    2a0300;      3;21:00:00:1b:32:10:1a:00;20:00:00:1b:32:10:1a:00; na
    FC4s: FCP 
    NodeSymb: [38] "QLE2460 FW:v5.06.05 DVR:v902.k1.1-9vmw"
    Fabric Port Name: 20:03:00:05:1e:34:c5:ef 
    Permanent Port Name: 21:00:00:1b:32:10:1a:00
    Port Index: 3
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases: esx01_p1
 N    2a0400;      3;20:35:00:80:e5:2e:c7:02;20:04:00:80:e5:2e:c7:02; na
    FC4s: FCP [IBM     1746      FAStT 1070]
    Fabric Port Name: 20:04:00:05:1e:34:c5:ef 
    Permanent Port Name: 20:35:00:80:e5:2e:c7:02
    Port Index: 4
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases: ds3524_b_p1
 N    2a0500;    2,3;20:0f:00:c0:dd:28:7e:d6;10:00:00:c0:dd:28:7e:d6; na
    Fabric Port Name: 20:05:00:05:1e:34:c5:ef 
    Permanent Port Name: 20:0f:00:c0:dd:28:7e:d6
    Port Index: 5
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases:
 N    2a0501;    2,3;21:00:00:24:ff:3f:a9:df;20:00:00:24:ff:3f:a9:df; na
    Fabric Port Name: 20:05:00:05:1e:34:c5:ef 
    Permanent Port Name: 20:0f:00:c0:dd:28:7e:d6
    Port Index: 5
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases: p7vios1_fcs1
 N    2a0f00;      3;50:03:08:c3:a1:78:a0:01;50:03:08:c3:a1:78:a0:00; na
    FC4s: FCP [IBM     ULT3580-TD6     D2D2]
    Fabric Port Name: 20:0f:00:05:1e:34:c5:ef 
    Permanent Port Name: 50:03:08:c3:a1:78:a0:01
    Port Index: 15
    Share Area: No
    Device Shared in Other AD: No
    Redirect: No 
    Aliases: drive_1
    ...........
The Local Name Server has 15 entries }
</cli>

===== Brocade commands =====

<cli prompt='#'>
aaaconfig                  Configure RADIUS for AAA services
ad                         Specifies all administration domain (AD)-level
                           operations
ag                         Configure the Access Gateway feature
agshow                     Displays the Access Gateway information registered
                           with the fabric
agtcfgdefault              Reset SNMP agent to factory default
aliadd                     Add a member to a zone alias
alicreate                  Create a zone alias
alidelete                  Delete a zone alias
aliremove                  Remove a member from a zone alias
alishow                    Print zone alias information
aptpolicy                  Get and set Advanced Performance Tuning policy
auditcfg                   Modifies and displays audit log filter
                           configuration.
auditdump                  Display audit log
authutil                   Get and set authentication configuration
backplanetest              Backplane connection test for multi-blade systems.
backport                   Test for back-end ASIC pair to ASIC pair links.
bannerset                  Set security banner
bannershow                 Display security banner
bcastshow                  Display broadcast routing information
bladebeacon                Enables or disables blade beaconing or displays the
                           current mode.
bladedisable               Disables all user ports on a blade.
bladeenable                Enables all User Ports on a blade.
bpportloopbacktest         Functional test of port via blade processor path.
bpturboramtest             MBIST test for AP blade BP ASICs
burninerrclear             Clear errors that are stored in the non-volatile
                           storage
burninerrshow              Display errors that are stored in the non-volatile
                           storage
burninstatus               Display the diagnostics burnin status.
camtest                    Verify QuickLoop's Content Addressable Memory
                           (CAM).SID translation
centralmemorytest          Test ASIC central memory operation.
cfgactvshow                Display Effective zone configuration information
cfgadd                     Add a member to a configuration
cfgclear                   Clear all zone configurations
cfgcreate                  Create a zone configuration
cfgdelete                  Delete a zone configuration
cfgdisable                 Disable a zone configuration
cfgenable                  Enable a zone configuration
cfgmcdtmode                Configure legacy MCDT zoning behavior
cfgremove                  Remove a member from a configuration
cfgsave                    Save zone configurations in flash
cfgsaveactivetodefined     Moves the effective configuration to the defined
                           configuration
cfgshow                    Print zone configuration information
cfgsize                    Print size details of zone database
cfgtransabort              Abort zone configuration transaction
cfgtransshow               Print zone configurations in transaction buffer
chassisbeacon              Set chassis beacon on or off
chassisconfig              Display or set the chassis configuration
chassisdisable             Disable all ports in chassis
chassisenable              Enable all ports in chassis
chassisname                Display or set the chassis's Name
chassisshow                Display all Field Replaceable Units (FRU)
chipregshow                Displays the port registers for a given chip
                           number.
clihistory                 Displays a log of most recently executed CLI
                           commands
cmemretentiontest          Data retention test of the central memory SRAMs.
cmitest                    Verify CMI bus between ASICs.
configdefault              Reset config to factory default
configdownload             Load switch config from a server
configlist                 List the stored config files
configremove               Remove a stored config file
configshow                 Print switch config parameters
configupload               Save switch config to a server
configure                  Set logical switch config parameters
configurechassis           Set chassis config parameters
cryptocfg                  Configure encryption node functions
datatypeshow               Display available diagnostic data types.
date                       Print/set the system date and time
dbgshow                    Display debug levels of various modules
defzone                    Activates or deactivates a default zone
                           configuration.
diagclearerror             Clears diagnostics failure status.
diagcommandshow            Display diagnostic command descriptions.
diagdisablepost            Disable diagnostic POST.
diagenablepost             Enable diagnostic POST.
diagenv                    Diagnostic debug parameters management package.
diaghelp                   Display diagnostic command descriptions.
diagloopid                 Select the diagnostics loop ID.
diagmodeshow               Displays diagnostic mode configuration.
diagpost                   Displays the contents of port registers and
                           memories.
diagretry                  Sets diagnostic retry mode
diagsetburnin              Initializes the blade for a burnin run.
diagsetcycle               Set diagnostic script parameters.
diagsetesdmode             Set or display ESD mode.
diagsetshowtime            Set or display diagnostic show-time mode.
diagshow                   Display diagnostic status.
diagshowtime               Set or display diagnostic show-time mode.
diagstatus                 Display currently running diagnostic tests.
diagstopburnin             Terminate burnin run on a blade.
distribute                 Distributes data to switches in a fabric.
dlsreset                   Turn off the dynamic load sharing (DLS) option
dlsset                     Turn on the dynamic load sharing (DLS) option
dlsshow                    Display the state of the dynamic load sharing
                           option
dnsconfig                  Configure DNS service
enclosureshow              Display the switch enclosure attributes
errclear                   Clear error log
errdelimiterset            Sets the error log start and end delimiter for
                           messages sent to the console and syslog
errdump                    Print error log (no page breaks)
errfilterset               Sets a filter for an error log destination
errmoduleshow              Displays all the defined modules in the system
errshow                    Print error log
fabportshow                Display contents of a particular port's data
fabretryshow               Display retry count of various fabric commands
fabriclog                  Displays or manipulates the fabric log
fabricprincipal            Configure Principal Switch Selection mode
fabricshow                 Print fabric membership info
fabstateclear              Clears the fabric state information
fabstateresize             Changes the number of state entries
fabstateshow               Displays the fabric state information
fabstatsshow               Displays the fabric statistics information
fabswitchshow              Display fabric switch state information
fandisable                 Disables a fan unit.
fanenable                  Enables a fan unit.
fanshow                    Print fan status
fastboot                   Reboot this switch and bypass POST
fastwritecfg               Configure FC fastwrite feature
fcipchiptest               Functional Test of Components in FCIP Complex.
fciphelp                   Print FCIP help info
fcippathtest               Data Path Test of the FCIP complex.
fcping                     Sends a FC ELS ECHO request to a port
fcplogclear                Clear the FCP log
fcplogdisable              Disable logging of FCP events
fcplogenable               Enable logging of FCP events
fcplogshow                 Display FCP probing log information
fcpprobeshow               Display FCP probing information
fcprlsshow                 Display FCP RLS (read link state) information
fcrbcastconfig             Configure interfabric broadcast frame forwarding
fcrchiptest                Functional Test of FCR FPGA.
fcrconfigure               Sets FC Router configuration parameters.
fcrfabricshow              Displays FC Routers on a backbone fabric.
fcrlsan                    Configure LSAN policies
fcrlsancount               Display maximum LSAN zone limit.
fcrlsanmatrix              Manage LSAN fabric matrix configuration.
fcrpathtest                Data Path Test on Connection between FCR FPGA and
                           Central ASIC.
fcrphydevshow              Displays FC Router physical device information.
fcrproxyconfig             Displays or configures proxy devices presented by
                           an FC Router.
fcrproxydevshow            Displays FC Router proxy device information.
fcrresourceshow            Displays FC Router physical resource usage.
fcrrouterportcost          Modify FC Router port cost configuration.
fcrrouteshow               Displays FC Router route information.
fcrxlateconfig             Displays or persistently configures a translate
                           (xlate) domain's domain ID for both
                           EX_Port-attached fabric and backbone fabric.
fddcfg                     fddcfg manages the fabric data distribution
                           configuration parameters.
fdmicacheshow              Display abbreviated remote FDMI device information
                           according to remote domain ID
fdmishow                   Display detailed FDMI device information
ficonclear                 Clears contents of the specified FICON management
                           database
ficoncupset                Sets FICON-CUP parameters for a switch
ficoncupshow               Displays FICON-CUP parameters for a switch
ficonhelp                  Displays FICON commands
ficonshow                  Displays contents of the specified FICON management
                           database
filtertest                 Run frame filter test for bloom ASICs.
fipscfg                    Configure FIPS mode operation
firmwarecommit             Commit firmware to stable storage
firmwaredownload           Download firmware into switch
firmwaredownloadstatus     Display the progress and status of firmwareDownload
firmwarekeyshow            Manage the keys used to check firmware signatures
firmwarekeyupdate          Manage the keys used to check firmware signatures
firmwarerestore            Restore the old firmware in the switch
firmwareshow               Display firmware versions in the switch
fosconfig                  Enable/disable FabOS services
fosexec                    Invoke command in alternate VF context
fporttest                  Functional test of F->N N->F point to point path.
framerpathtest             Tests data path between ASICs
frureplace                 Replace a Field Replacable Unit
fspfshow                   Print FSPF global information
fwalarmsfilterset          Configure alarms filtering for Fabric Watch
fwalarmsfiltershow         Show alarms filtering for Fabric Watch
fwclassinit                Initialize all Fabric Watch classes
fwconfigreload             Reload Fabric Watch configuration
fwconfigure                Configure Fabric Watch
fwfrucfg                   Configure FRU state and notification
fwhelp                     Print Fabric Watch help info
fwmailcfg                  Configure Fabric Watch Email Alert
fwportdetailshow           Create a report with detailed port information
fwsamshow                  Show availability monitor information
fwset                      Set port persistence time
fwsettocustom              Set boundary & alarm level to custom
fwsettodefault             Set boundary & alarm level to default
fwshow                     Show thresholds monitored and port persistence time
grep                       Linux grep command
h                          Print shell history
hadisable                  Disables the High Availability feature in the
                           switch.
hadump                     Displays information about the status of the High
                           Availability feature in the switch.
haenable                   Enables the High Availability feature in the switch
hafailover                 Forces the failover mechanism so that the Standby
                           Control Processor (CP)becomes the Active CP.
hashow                     Displays control processor (CP) status
hasyncstart                Enables HA state synchronization.
hasyncstop                 Disables the HA state synchronization.
help                       Print this list
historylastshow            Displays last history record
historymode                Display or set the mode of the history log
historyshow                Displays entire history log
httpcfgshow                Used to show the version of the Java plug-in used
                           by the Webtools
i                          Display process summary
iclcfg                     Configure ICL state
ifmodeset                  Set the link operating mode for a network interface
ifmodeshow                 Display the link operating mode for a network
                           interface
interfaceshow              Display the FSPF (TM) interface information
interopmode                Displays/enables/disables Brocade switch
                           interoperability with switches from other
                           manufacturers
ioddelayreset              Configure in-order-delivery (IOD) delay parameter
ioddelayset                Configure in-order-delivery (IOD) delay parameter
ioddelayshow               Configure in-order-delivery (IOD) delay parameter
iodreset                   Turn off the in-order delivery (IOD) option
iodset                     Manage the in-order delivery (IOD) option
iodshow                    Display the state of the in-order delivery option
ipaddrset                  Set ethernet and FC IP addresses
ipaddrshow                 Print ethernet and FC IP addresses
ipfilter                   Manage/display IP filters
ipsecconfig                Configure IPSec feature
iscsihelp                  Print iSCSI help info
islshow                    Display the current connections and status
killtelnet                 Terminate telnet/serial login sessions
                           interactively
ldapcfg                    Configure LDAP role mapping
ledtest                    Cycle system LEDs.
lfcfg                      Configure logical fabrics
lfexec                     Invoke command in alternate VF context
licenseadd                 Adds license keys to switch
licensehelp                Print license help info
licenseidshow              Displays the system license ID
licenseport                Configure per-port POD license assignments
licenseremove              Removes a license key from this system
licenseshow                Displays current license keys
linkcost                   Set or print the FSPF cost of a link
login                      Login as a new user
logout                     Logout from remote session
loopporttest               Functional test of L-port M->M path on a loop.
lscfg                      Configure logical switches
lsdbshow                   Displays the FSPF link state database
memshow                    Display memory usage in the system.
minispropshow              Displays ASIC pair properties.
more                       Linux more command
mscapabilityshow           Display Management Server Capability.
msconfigure                Configure Management Server
msplatshow                 Display the Management Server Platform Database
msplatshowdbcb             Display the Management Server Database Control
                           Block
msplcleardb                Clear the Management Server Platform Database
                           fabric-wide
msplmgmtactivate           Activate the Management Server Platform Database
                           fabric-wide
msplmgmtdeactivate         Deactivate the Management Server Platform Database
                           fabric-wide
mstddisable                Disables the Management Server Topology Discovery
                           Management Service
mstdenable                 Enables the Management Server Topology Discovery
                           Management Service
mstdreadconfig             Display status of Management Server Topology
                           Discovery Service
myid                       Display the current login session details
nbrstateshow               Display FSPF (TM) neighbors' states
nbrstatsclear              Reset the FSPF (TM) interface counters
netstat                    Display network connections and statistics
nodefind                   Display all the devices' PID matching the given
                           world wide name
nsaliasshow                Display local Name Server information with Aliases
nsallshow                  Print global Name Server information
nscamshow                  Print local Name Server Cache information
nsshow                     Print local Name Server information information
nszonemember               Display the information of all the online devices
                           which are zoned with the given device.
opensource                 Display information on open source software
                           utilized in FabOS
passwd                     Set usernames and passwords
passwdcfg                  passwdcfg manages the password policies.
pathinfo                   Display routing information between two ports
pdshow                     Show information from Panic Dump file
perfaddeemonitor           Add end-to-end monitor
perfaddipmonitor           Add monitor for IP trafic frame count
perfaddreadmonitor         Add filter-based monitor - SCSI Read
perfaddrwmonitor           Add monitor - SCSI Read and Write
perfaddscsimonitor         Add monitor for SCSI frame count
perfaddusermonitor         Add filter-based monitor
perfaddwritemonitor        Add filter-based monitor - SCSI Write
perfcfgclear               Clear Performance settings from FLASH
perfcfgrestore             Restore Performance configuration from FLASH
perfcfgsave                Save Performance configuration to FLASH
perfclearalpacrc           Clears the CRC error count associated with a port
                           and Arbitrated Loop Physical Address (AL_PA).
perfcleareemonitor         Clears statistics counters of one or more
                           end-to-end performance monitors.
perfclearfiltermonitor     Clears counters of one or more filter-based
                           performance monitors.
perfdeleemonitor           Delete end-to-end monitor
perfdelfiltermonitor       Delete filter-based monitor
perfhelp                   Print Performance Monitoring help info
perfmonitorclear           Clear end-to-end/filter-based/ISL monitors
perfmonitorshow            Show end-to-end/filter-based/ISL monitors
perfsetporteemask          Set overall mask for end-to-end monitors
perfshowalpacrc            Get ALPA CRC count by port and ALPA
perfshoweemonitor          Show user-defined end-to-end monitors
perfshowfiltermonitor      Show filter-based monitors
perfshowporteemask         Show the current end-to-end mask
perfttmon                  Configure bandwidth usage monitor
ping                       Display the link operating mode for a network
                           interface
ping6                      Display the link operating mode for a network
                           interface
pkicreate                  Creates public key infrastructure (PKI) objects
pkiremove                  Removes existing public key infrastructure (PKI)
                           objects
pkishow                    Displays existing public key infrastructure (PKI)
                           objects
policy                     Configure IPSec encryption and authentication
                           algorithms
portaddress                Configure low 16 bits of Fibre Channel Porrt ID
portalpashow               Show the ALPAs of a port
portbuffershow             Print the buffer allocations for the ports of a
                           quad
portcamshow                Display filter utilization
portcfg                    Create/Delete a new ip interface/route/arp entry on
                           the GigE port
portcfgalpa                Set AL_PA to 0x0 (default) or 0x13
portcfgautodisable         Configure auto disable
portcfgcreditrecovery      Configure credit recovery
portcfgdefault             Restore the port configuration to defaults
portcfgeport               Enable/Disable a port from becoming E_Port
portcfgexport              Sets a port to be an EX_Port and sets and displays
                           EX_Port configuration parameters.
portcfgfillword            Configure a port to a particular fill word
portcfgfportbuffers        Configure F_Port buffers
portcfggport               Lock a port as a G_Port
portcfgislmode             Configure a port to be ISL R_RDY Mode
                           enabled/disabled
portcfglongdistance        Configure a Long Distance Port
portcfglosstov             Configure frontend port signal debounce
portcfglport               Lock a port as a L_Port
portcfgnpivport            Enables and disables NPIV functionality on a port.
portcfgnport               Enable/disable N_Port capability for a port
portcfgpersistentdisable   Persistently disable a port
portcfgpersistentenable    Enable a persistently disabled port
portcfgqos                 Configure QoS feature
portcfgshow                Displays port configuration settings.
portcfgspeed               Configure a port to a particular speed level
portcfgtrunkport           Configure a port for trunking
portcfgvexport             Sets a port to be an VEX_Port connected to FC-IP
                           and sets and displays VEX_Port configuration
                           parameters.
portcmd                    Execute commands (ping etc) on the GigE port
portdebug                  Set debug level and verbosity level of port modules
portdisable                Disable a specified port
portenable                 Enable a specified port
porterrshow                Print port error summary
portflagsshow              Display the port status bitmaps of all ports in a
                           switch
portledtest                Cycle user port LEDs.
portlogclear               Clear port activity log
portlogconfigshow          Display portlog configuration
portlogdisable             Disable portlog facility
portlogdump                Print port log (no page breaks)
portlogdumpport            Print port log (no page breaks)
portlogenable              Enables port log facility
portlogeventshow           Display information about port log events
portloginshow              Display port login information
portlogpdisc               Set or clear the debug_pdisc_flag
portlogreset               Enable portlog facility
portlogresize              Resize the port log
portlogshow                Print port activity log
portlogshowport            Print port activity log
portlogtypedisable         Disable port logging
portlogtypeenable          Enable port logging
portloopbacktest           Functional test of port N->N path.
portmirror                 Set a port's configuration to be disabled or
                           enabled
portname                   Assign or display the name associated with a port
portperfshow               Print port throughput numbers
portregtest                Write/read test of the ASIC SRAMs portregtest.
portrouteshow              Display various routing tables for a port
portshow                   Show configured ip interfaces/routes/arp entries on
                           the GigE Port
portstats64show            Display the 64-bit hardware statistics for a port
portstatsclear             Clear the status of a specified switch port
portstatsshow              Print hardware statistics
portswap                   Swaps area numbers
portswapdisable            Disable portswap feature
portswapenable             Enable portswap feature
portswapshow               Display port and area information
porttest                   Functional test on a live fabric. Starts porttest.
porttestshow               Retreive information from porttest.
porttrunkarea              Configure area trunking
portzoneshow               Displays the enforced zone type of the F/FL-ports
                           of a switch.
powerofflistset            sets slot power off list order
powerofflistshow           Displays slot power-off order.
psshow                     Print power supply status
quietmode                  Displays/enables/disables quietmode on telnet
                           session
reboot                     Reboot this processor
routehelp                  Print routing help info
saschiptest                Functional Test of Components in SAS Complex.
saspathtest                Data Path Test of the SAS complex.
secactivesize              Displays size of the active (security) database
secauthsecret              Creates/Manages DHCHAP secret key details
seccertutil                Creates/Manages/Displays third party PKI
                           certificates
secdefinesize              Displays size of the defined (security) database
secglobalshow              Displays current internal security state
                           information
sechelp                    Displays information about security commands
secpolicyabort             Aborts changes to defined policy
secpolicyactivate          Activates all policy sets
secpolicyadd               Adds members to an existing policy
secpolicycreate            Creates a new policy
secpolicydelete            Deletes an existing policy
secpolicydump              Displays all members of existing policies
secpolicyfcsmove           Moves a member in the FCS policy
secpolicyremove            Removes members from an existing policy
secpolicysave              Saves defined policy set and sends to all switches
secpolicyshow              Shows members of one or more policies
secstatsreset              Resets security statistics
secstatsshow               Displays security statistics
sensorshow                 Display sensor readings
setdbg                     Set debug level of the specified module
setesdmode                 Set or display ESD mode.
setmfgmode                 Set or display diagnostic MFG mode.
setmodem                   Enables or disables modem login to a control
                           processor (CP)
setsplbmode                Set or display SPLB mode.
setverbose                 Set verbosity level of the specified module
sfpshow                    Print Serial ID SFP information
shellflowcontroldisable    Disable xon-xoff flow control on console serial
                           port
shellflowcontrolenable     Enable xon-xoff flow control on console serial port
slotpoweroff               Removes power from a slot.
slotpoweron                Restores power to a slot.
slotshow                   Displays the status of all slots in the system.
sltest                     Serial link test of port N->N path.
snmpconfig                 Configure SNMP
snmpmibcapset              Set options for configuring SNMP Mib/Trap
                           Capability
snmpmibcapshow             Show SNMP Mib/Trap Configuration
spinfab                    Functional test of switch to switch ISL cabling and
                           trunk group operation.
spinjitter                 line-speed jitter measurement
spinsilk                   Functional test of internal and external transmit
                           and receive paths at full speed
sramretentiontest          Data retention test of the miscellaneous SRAMs in
                           ASIC.
sshutil                    Configure SSH authentication options
statsclear                 Clear port and diagnostic statistics.
statstest                  Statistics counter test for the ASICs.
stopporttest               Terminate the running porttest.
supportffdc                Modifies or displays first-failure data capture
                           (FFDC) configuration.
supportftp                 set support Ftp parameters
supportsave                retrieve support data from switch to host
supportshow                Prints switch information for debugging purposes.
supportshowcfgdisable      Disables a group of commands under supportshow
                           command.
supportshowcfgenable       Enables a group of commands under supportshow
                           command.
supportshowcfgshow         Displays the groups of commands enabled for
                           display. by the supportshow command.
switchbeacon               Set switch beacon on or off
switchcfgpersistentdisable Persistently disable a switch
switchcfgpersistentenable  Enable a persistently disabled switch
switchcfgspeed             Configures all ports of the switch to a particular
                           speed level
switchcfgtrunk             Configure all ports on the switch for trunking
switchdisable              Disable this switch
switchenable               Enable this switch
switchname                 Print/set this switch's name
switchshow                 Print switch and port status
switchstatuspolicyset      Set policy parameters for overall switch status
switchstatuspolicyshow     Print policy parameters for overall switch status
switchstatusshow           Print overall switch status
switchuptime               Display the amount of time for which the switch is
                           up
switchviolation            Display policy violations recorded in RAS log
syslogdfacility            Change the syslog facility
syslogdipadd               Add syslog daemon IP address
syslogdipremove            Remove syslog daemon IP address
syslogdipshow              Print the syslog daemon targets
sysshutdown                Provides a graceful shutdown to protect the switch
                           file systems.
systemverification         Run a suit of diagnostic tests on all switches in a
                           system.
tempshow                   Print temperature readings
timeout                    Set/show the IDLE timeout value for a login session
topologyshow               Display the unicast fabric topology
tracedump                  generate/remove trace dump or display trace dump
                           status
traceftp                   enable/disable trace auto-FTP or transfer trace
                           dump
trackchangeshelp           Print Track Changes help info
trackchangesset            Configure alert for login/logout/config update
trackchangesshow           Displays status of track changes
trunkdebug                 Debug a trunk link failure
trunkshow                  Display trunking information
tsclockserver              Displays or sets the NTP server address
tstimezone                 Displays or sets the time zone
turboramtest               Turbo SRAM test for bloom ASICs.
txdpath                    Functional test of ASIC pair TXA TXD connections.
uptime                     Print how long switch has been up
urouteconfig               Configure a static route
urouteremove               Remove a static route
urouteshow                 Display unicast routing information
usbstorage                 Manage USB storage device (available on Brocade
                           Data Center Director only).
userconfig                 Display or configure user accounts
userrename                 Rename user login name
version                    Print firmware version
wwn                        Display or set the world wide name
zone                       Configure zone objects
zoneadd                    Add a member to a zone
zonecreate                 Create a zone
zonedelete                 Delete a zone
zonehelp                   Print zoning help info
zoneobjectcopy             Copies a zone object
zoneobjectexpunge          Expunges a zone object
zoneobjectrename           Rename a zoning Object
zoneremove                 Remove a member from a zone
zoneshow                   Print zone information
</cli>


http://wikibon.org/wiki/v/How_to_configure_FCIP_on_Brocade_7500%27s

===== Scripts to recreate zoning =====

If you have save the zoning from an old switch using the **configupload** command, you can recreate it on the new one using the following scripts:

  for line in $(grep -p Zoning config.txt | grep "^alias.")
  do
    echo $line | sed 's/\./\ /1' | sed 's/alias/alicreate/1' | sed 's/\:/\,"/1' | sed 's/$/"/'
  done

  for line in $(grep -p Zoning config.txt | grep "^zone.")
  do
    echo $line | sed 's/\./\ /1' | sed 's/zone/zonecreate/1' | sed 's/\:/\,"/1' | sed 's/$/"/'
  done

  for line in $(grep -p Zoning config.txt | grep "^cfg.")
  do
    echo $line | sed 's/\./\ /1' | sed 's/cfg/cfgcreate/1' | sed 's/\:/\,"/1' | sed 's/$/"/'
  done
  
Now you can **cfgsave** and **cfgenable** to activate the new configuration.

===== Scripts to convert WWN with : format =====

convert_wwn.ksh
<code>
#!/bin/ksh93
#set -x
# convert a WWN aabbcc to aa:bb:cc
# or AB.AC.12 to ab:ac:12

convert_wwn ()
{
wwn=$1
wwn_nodot=$(echo $wwn | sed 's/://g;s/\.//g' | tr 'a-z' 'A-Z')
wwn_dot=$(echo $wwn_nodot | sed 's/../&:/g;s/:$//' | tr 'A-Z' 'a-z')
echo $wwn_dot
}

convert_wwn $1
</code>

===== List the full switch configuration, and zoning =====

<cli prompt='>'>
swsan1:admin> configshow -all 
[Configuration upload Information]
Configuration Format = 2.0
date = Thu Jan  9 17:31:06 2014
FOS version = v6.4.3.0
Number of LS = 0
[Chassis Configuration Begin]

[fcRouting]

[Chassis Configuration]
SB_License.FTR_10G.slots:0x0
SB_License.FTR_AE.slots:0x0
SB_License.FTR_AFA.slots:0x0
cfgload.secure:0
cfgload.signed:0
diag.postDisable:0
enhancedLicensing.enabled:0
fips.mode:0
fips.promallow:1
fips.selftests:0
http.accesslog:
.....
ipfilter.1.type:1
passwdcfg.adminlockout:0
passwdcfg.digits:0
passwdcfg.history:1
passwdcfg.lockoutduration:30
passwdcfg.lockoutthreshold:0
passwdcfg.lowercase:0
passwdcfg.maxpasswordage:0
passwdcfg.minlength:8
passwdcfg.minpasswordage:0
passwdcfg.punctuation:0
passwdcfg.repeat:1
passwdcfg.sequence:1
passwdcfg.status:0
passwdcfg.uppercase:0
passwdcfg.warning:0
....
[Zoning]
cfg.cfg_A:z_ds3500_esxtest;z_ds3512_tsmtest2;z_luds3512_arwen_fcs1;z_luds3512_luitesxlab1_p0;z_luds3524_arwen_fcs1;z_luds3524_luitesx1_p0;z_luds3524_luitesx2_p0;z_luds3524_luitesx3_p0;z_luds3524_luitesxlab1_p0;z_luds3524_p550_vios1_fcs0;z_luds3524_p550_vios2_fcs0;z_luds3524_p7vios1_fcs0;z_luds3950_arwen_fcs1;z_luds3950_luitesxlab1_p0;z_luds3950_p7samba_fcs0;z_luds3950_p7vios1;z_ts3310_arwen_fcs1;z_ts3584_tsmtest2;z_v7000U1_esxlab1
zone.z_ds3500_esxtest:esx1_test;esx2_test;luds3512_a_p3;luds3512_b_p3;luds3524_a_p3;luds3524_b_p3;luds3950_a_p2;luds3950_b_p1
zone.z_ds3512_tsmtest2:luds3512_a_p3;luds3512_b_p3;tsmtest2
zone.z_luds3512_luitesxlab1_p0:luds3512_a_p3;luds3512_b_p3;luitesxlab1_p0
zone.z_luds3524_arwen_fcs1:arwen_fcs1;luds3524_a_p3;luds3524_b_p3
....
alias.TS3584_drive_1:50:05:07:63:0f:03:6b:01
alias.TS3584_drive_2:50:05:07:63:0f:03:6b:02
alias.V7000U1P1:50:05:07:68:02:30:c8:e9
alias.p7_samba_fcs0:c0:50:76:06:9f:15:00:04
alias.p7vios1_fcs0:21:00:00:24:ff:3f:a9:de
alias.powerha1_fcs0:c0:50:76:06:9f:15:00:16;c0:50:76:06:9f:15:00:17
alias.powerha2_fcs0:c0:50:76:06:9f:15:00:1a;c0:50:76:06:9f:15:00:1b
....
defzone:noaccess
enable:cfg_A
...
</cli>
 

===== Additional commands =====

  userConfig --add <username> -r <rolename>

username Specifies the account name, which must begin with an alphabetic character. The name can be from 8 to 40 characters long. It is case-sensitive and can contain alphabetic and numeric characters,the period (.) and the underscore ( _ ). It must be different than all other account names on the logical switch. The account name cannot be the same as a role name.

  -r rolename Specifies the role: User, SwitchAdmin, ZoneAdmin, FabricAdmin, BasicSwitchAdmin, Operator, or Admin in nonsecure mode; in secure mode you can also use NonfcsAdmin.
  -h admindomain_ID Optional: Specifies the home Administrative Domain; if no Administrative Domain is specified, then the lowest numbered Administrative Domain in the list is assigned.

  -a admindomain_ID_list Optional: Specifies which Administrative Domains the user may access; if no Administrative Domains are listed, the user is automatically assigned to AD0. Use comma-separated lists, ranges, or both for example -a 0,9,10-15,244.
  -d description Optional: Adds a description to the account. The description field can be up to 40 printable ASCII characters long. The following characters are not allowed: asterisk (*), single quotation mark (‘),quotation mark (“), exclamation point (!), semicolon (:smileywink:, and colon (:smileyhappy:.
  -x Specifies an expired password that must be changed the first time the user logs in.

  userConfig --add toto -r admin -d "Toto Account"
  
===== Default login/password =====

Default password for user:
  admin   password
  root    fibranne


https://www.ibm.com/developerworks/community/blogs/sanblog/entry/how_to_list_all_zones_to_which_a_wwpn_belongs?lang=en

==== Viewing a summary switch status report ====

A summary view provides health status at a high level and includes enough information for you to investigate further if necessary.

To view a summary switch status report, complete the following steps.
<cli prompt='>'>
switch:admin> mapsdb --show 

1 Dashboard Information:
=======================
DB start time:                  Tue Mar  3 22:27:52 2015
Active policy:                  dflt_aggressive_policy
Configured Notifications:       RASLOG
Fenced Ports :                  None
Decommissioned Ports :          None
Quarantined Ports :             None

2 Switch Health Report:
=======================
Current Switch Policy Status: MARGINAL
Contributing Factors:
---------------------
*BAD_PWR (MARGINAL).
*BAD_FAN (MARGINAL).


3.1 Summary Report:
===================
Category                 |Today                     |Last 7 days               |
--------------------------------------------------------------------------------
Port Health              |No Errors                 |No Errors                 |
BE Port Health           |No Errors                 |No Errors                 |
Fru Health               |Out of operating range    |In operating range        |
Security Violations      |No Errors                 |No Errors                 |
Fabric State Changes     |No Errors                 |No Errors                 |
Switch Resource          |In operating range        |In operating range        |
Traffic Performance      |In operating range        |In operating range        |
FCIP Health              |Not applicable            |Not applicable            |
Fabric Performance Impact|In operating range        |In operating range        |
</cli>

==== Virtual Fabric ====

Enable virtual fabric feature
  fosconfig --enable vf

List virtual fabric FID
  lscfg --show

To change context 
  setcontext fabricID | switchname 
  
Create a new virtual fabric with FID
  lscfg --create FID
  
Assign a port to a virtual fabric (port will be disabled for this operation)
  lscfg --config 99 -port 5

FIXME To use fosexec, you have to allow it into **configure** to authorize **Remote fosexec feature**

Start a command under a specific fabric ID (FID)FID can be all
  fosexec --fid FID -cmd "command"
  
==== Hard Zoning ====

While hard zoning, per port is not recommended, it can be useful in specific situation
  port are identified by the switchDomain ID (switchshow) and port number
  Ex: zonecreate hard_zone,"3,0;3,1;3,2"
  
==== Release and Reserve a Brocade Port License from CLI ====

Change activation licensed ports (Port on demand)
<cli prompt='>'>
sansw1:FID128:admin> switchshow
switchName:     sansw1
...
Allow XISL Use: ON
LS Attributes:  [FID: 128, Base Switch: No, Default Switch: Yes, Ficon Switch: No, Address Mode 0]

Index Port Address  Media Speed   State       Proto
==================================================
   0   0   150000   id    N32     No_Light    FC  (Ports on Demand license not assigned or reserved yet)
   1   1   150100   id    N32     No_Light    FC  (Ports on Demand license not assigned or reserved yet)
   2   2   150200   id    N32     No_Light    FC  (Ports on Demand license not assigned or reserved yet)
   3   3   290300   id    N32     No_Light    FC
   4   4   290400   id    N32     No_Light    FC
</cli>

<cli prompt='>'>
sansw1:FID128:admin> licenseshow
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx:
    Ports on Demand license
    Capacity 24
</cli>

<cli prompt='>'>
sansw1:FID128:admin> licenseport --show
   48 SFP-based ports are available in this switch
   16 QSFP-based ports are available in this switch
   Ports on Demand license is installed
   No Q-Flex Ports on Demand license is installed
     Dynamic POD method is in use

   48 SFP-based port assignments are provisioned for use in this switch:
        24 SFP-based port assignments are provisioned by the base switch allowance
        24 SFP-based port assignments are provisioned by the Ports on Demand license
   48 SFP-based ports are assigned to the base switch allowance or installed licenses:
        24 ports are assigned to the Ports on Demand base switch allowance
        24 SFP-based ports are assigned to the Ports on Demand license
  SFP-based ports assigned to the base switch allowance:
     3*, 4*, 5*, 6*, 7*, 8*, 10*
     32, 33, 34, 35, 36*, 37*, 38*, 39*, 40, 41
     42, 43, 44, 45
  SFP-based ports assigned to the Ports on Demand license:
     9*, 11*, 12*, 13*, 14*, 15*, 16*, 17*, 18*, 19*
     20*, 21*, 22*, 23*, 24*, 25*, 26*, 27*, 28*, 29*
     30*, 31*, 46*, 47*
  SFP-based ports that are not assigned:
     None
   10 license reservations are still available for use by unassigned ports
     0, 1, 2
  38 license assignments are held by offline ports (indicated by *)
</cli>

Enable license (reserve) to a port or range 0-2
<cli prompt='>'>
sansw1:FID128:admin> licenseport --reserve 0-2
</cli>
wiki

User Tools

Site Tools

Page Tools
